 鲜花( 48)  鸡蛋( 0)
|
also check this:
) |/ @$ F9 N3 [4 p/ ? c
% ?) @4 e4 U' F' b1 q2 F+ zPressing for one second arms the system by activating the
8 x9 W0 j$ k- q1 wstarter kill and locking the doors (if the door locks are connected).
2 _, k1 e. }- A N2 E6 o c6 uThe horn will honk (if connected) and the parking lights will flash
' K7 n4 B1 e4 F4 N: s; e, F( aonce to confirm arming of the system. While the system is armed,
/ J6 L) l. }8 S0 F, [" C# e# kthe status LED will flash once per second. The Failsafe® Starter Kill
3 U8 Q/ t; F+ J2 F(if installed) will also prevent the vehicle’s starter from cranking.4 `: u5 K, D( S& W- U- h
Arming
1 R/ V: J0 n& u. j© 2005 Directed Electronics—all rights reserved 9
: k) b4 H5 M* W9 AThe system can also be programmed to arm the optional Failsafe®6 a% m# m u9 R2 q, g% q* p- x: p
Starter Kill automatically (called Passive Mode). If the system has5 d/ |- l8 F8 a- S) }6 U. Z- h& o
been programmed for Passive Mode, the Failsafe® Starter Kill will# B: v. {4 f$ S! D( O
automatically activate 30 seconds after the ignition has been2 ]$ L. n, l6 A' M
turned off. After the ignition has been turned off, the status LED0 C9 Q/ G4 x( B I* s, f6 D$ _
will flash rapidly to indicate that the system is in Passive Mode., G( i( [! \. K* w1 D/ @
If Passive Mode has been programmed on, then it is also possible
& j% {6 V. m% ` [to program the system for Passive Locking. With Passive Locking,: l9 Z; u6 w1 o Y- C
the vehicle doors lock automatically at the same time that the Failsafe®7 T! _+ |# O' X* X+ J, K- _
Starter Kill is activated. If Passive Locking is programmed on, care9 d5 Y' J! |( E1 f1 S! U5 }
must be taken to prevent the keys from being locked in the vehicle.+ {# w1 \' v1 W* n4 V
NOTE: For Passive Mode to be effective, the Failsafe® Starter Kill relay
5 z( e8 w G/ h; j! zmust be installed.
, u4 g! G y2 U, u$ BPressing for one second disarms the system and unlocks the
+ y$ @8 s1 P8 o; {8 Ndoors (if connected). The horn will honk twice (if connected) and
, f9 m4 v* a8 r6 [6 @the parking lights will flash twice to confirm disarming of the system.
( g: P8 @8 f% Y9 I1 | C0 f+ KThe optional Failsafe® Starter Kill will be deactivated. The status
4 B! o: b$ D! x+ FLED will turn off, unless the system is programmed for Passive, ? v" R0 G( v0 ]/ P
Mode. In Passive Mode, the status LED will flash rapidly when the9 K$ {0 k/ N/ P) p" W2 _0 l# t; l% [* v
system is disarmed. This indicates that the system will re-engage
9 M& i# y4 }! o- jthe starter kill and re-lock the doors (if Passive Locking has been5 T. A+ `- z3 v3 D" Z1 }+ F) Z
programmed) in 30 seconds unless the ignition is turned on.2 z8 ~7 {, O d3 N' N; n' S
Disarming
" ^7 j" Z8 A+ S/ W/ n10 © 2005 Directed Electronics—all rights reserved: Z& Q- q: A4 f' P
If your remote transmitter is lost or damaged, you can manually3 R( t: d. b+ G2 i7 Y, f" k
override the starter kill. To do this, you must have the vehicle's
* a6 |; @% O+ M9 P+ L4 b* jignition key and know where the Valet button is located. Be sure% I) P) D7 S- w2 T. L$ |8 @) _
to check with the installer for the location of the Valet button.! ^& |/ k" _- k
To override the starter kill, turn
' z7 Y( Y$ G- jthe ignition on and press the
, {+ z$ {" J3 R8 |Valet button within 10 seconds.7 }% Y5 w( q& U% H$ F
The status LED will stop flashing
4 k2 h+ ^; L! k/ Mand the vehicle should start. If it does not start,
) e, Z. d9 q m+ n- B3 u6 L8 tyou may have waited too long; turn the ignition off and repeat the
% M2 N3 i' e& j1 y3 ?5 eprocess.
+ k8 u! K# Z8 _) \- E$ y1 GLOCATION OF VALET BUTTON_____________________________
' q& x% m, M) }# f; wYou can prevent your system from automatically activating the4 \4 h s& P+ Y
Failsafe® Starter Kill and locking the doors by using Valet Mode.
( J$ F" a/ z/ s8 Y2 }This is very useful when washing the vehicle or having it serviced.
% B% M J7 o+ N/ A/ kIn Valet Mode, the starter kill cannot be activated, even with the1 K# w5 U/ g4 n5 v
transmitter, but all convenience functions (door locks, remote
( N& [! P, E, i5 W2 \% }6 kstart, etc.) will continue to work normally. |
|