 鲜花( 48)  鸡蛋( 0)
|
also check this:% e- i$ g1 j" l4 d
7 N' H* y3 E$ X6 B6 aPressing for one second arms the system by activating the0 p1 I% h# q7 v9 L
starter kill and locking the doors (if the door locks are connected).+ c& f, z6 a; `" Y4 h1 u- I
The horn will honk (if connected) and the parking lights will flash& e& h( ^+ f1 E. m; J
once to confirm arming of the system. While the system is armed,
( g- \' l0 r3 l6 V( mthe status LED will flash once per second. The Failsafe® Starter Kill: i6 _+ L9 J" P0 g0 H& _/ Z
(if installed) will also prevent the vehicle’s starter from cranking., W7 c, ~2 }+ Y9 c# Z3 A% [3 ^6 u
Arming) }. _ _0 T4 j J
© 2005 Directed Electronics—all rights reserved 9
- Z. M+ h5 ?1 H) J7 w0 ~4 RThe system can also be programmed to arm the optional Failsafe® i2 s$ Z2 k2 u% B% ]. x2 {# F) Z4 H
Starter Kill automatically (called Passive Mode). If the system has/ ] x1 `8 i. j6 [/ z
been programmed for Passive Mode, the Failsafe® Starter Kill will! ] O2 U0 s' o
automatically activate 30 seconds after the ignition has been
4 c) p8 N8 V+ z2 m( J% ]" Fturned off. After the ignition has been turned off, the status LED
2 Y, U2 h. t$ c2 Wwill flash rapidly to indicate that the system is in Passive Mode.
5 o- R+ a, p6 G7 ~- I; ~If Passive Mode has been programmed on, then it is also possible- Q9 A) s4 i+ t0 a5 E+ E5 p
to program the system for Passive Locking. With Passive Locking,+ s9 `( n4 U0 I* m) }7 K
the vehicle doors lock automatically at the same time that the Failsafe®
4 k7 v) Q; K9 d; jStarter Kill is activated. If Passive Locking is programmed on, care8 l3 C4 z! Y: u: d( t8 q7 v
must be taken to prevent the keys from being locked in the vehicle.; O% D' q$ c; b
NOTE: For Passive Mode to be effective, the Failsafe® Starter Kill relay
/ M! {) d+ f* B8 qmust be installed.
4 K1 D2 m2 A& f" \' m4 BPressing for one second disarms the system and unlocks the
& c6 i6 m6 H6 U2 V ydoors (if connected). The horn will honk twice (if connected) and
; z9 }% W+ L& t) y# Kthe parking lights will flash twice to confirm disarming of the system.
/ v- p( c3 m7 K2 x! LThe optional Failsafe® Starter Kill will be deactivated. The status z/ [* D7 H" B3 e2 O n$ X
LED will turn off, unless the system is programmed for Passive3 D/ J$ Y: F* [' N. K7 r& s
Mode. In Passive Mode, the status LED will flash rapidly when the4 h2 d% M. b) I- M' D6 v+ V- Q% F
system is disarmed. This indicates that the system will re-engage# o; j3 Q0 R5 ]0 D- _
the starter kill and re-lock the doors (if Passive Locking has been, G) c! |2 H, X; S) S, o X
programmed) in 30 seconds unless the ignition is turned on.
; {1 w; ?; p$ u& ~& Q: D. [Disarming
6 j+ i2 f2 ]+ E$ u10 © 2005 Directed Electronics—all rights reserved
6 E$ n9 s8 v R+ c! c; JIf your remote transmitter is lost or damaged, you can manually
2 U9 _$ a) m& j2 qoverride the starter kill. To do this, you must have the vehicle's2 u! A6 A" M, u: W0 r8 f g
ignition key and know where the Valet button is located. Be sure
7 x( x/ _0 k5 Y8 ~to check with the installer for the location of the Valet button.4 r3 G, A6 ]$ \+ x9 o2 f, [+ e, l
To override the starter kill, turn
/ C2 |( }) f7 I. L& Gthe ignition on and press the6 Y c; b" Z. A
Valet button within 10 seconds.
* T. o2 Q0 ^1 X ~The status LED will stop flashing1 }9 D( j% n3 Y& b$ }
and the vehicle should start. If it does not start,( L$ t; A9 {+ X
you may have waited too long; turn the ignition off and repeat the6 T, l/ [6 x/ R2 T
process.8 v; A8 r9 V1 w) y: J% P
LOCATION OF VALET BUTTON_____________________________
) j" ]9 G5 u7 Z5 a7 w/ k3 |You can prevent your system from automatically activating the+ ?2 A3 A i/ p. [) ?: ~+ H
Failsafe® Starter Kill and locking the doors by using Valet Mode.
0 A6 R# T& ?0 D7 N6 aThis is very useful when washing the vehicle or having it serviced.
. P0 E# b( P% ^+ s5 N: h/ VIn Valet Mode, the starter kill cannot be activated, even with the* o( w2 ~# ^6 ~$ f% c3 y' R
transmitter, but all convenience functions (door locks, remote) B. ]0 w# |/ c5 A. m. C* ~8 o
start, etc.) will continue to work normally. |
|