 鲜花( 48)  鸡蛋( 0)
|
also check this:
, S0 |" t7 J) Y( ] l
5 k& e o! ~4 ~3 g# m% VPressing for one second arms the system by activating the
$ n* \$ e) R8 \8 Z0 E( Q! astarter kill and locking the doors (if the door locks are connected).
! q: Z* G/ j. w* D% p: GThe horn will honk (if connected) and the parking lights will flash! k* {6 p" U3 Y$ n" c3 }
once to confirm arming of the system. While the system is armed,
% |; [( r/ S2 y9 Vthe status LED will flash once per second. The Failsafe® Starter Kill1 ]* a7 v4 f' p# q
(if installed) will also prevent the vehicle’s starter from cranking.
! x4 K) @# r' x" }! qArming9 Q, g4 R. S- Z, J2 ?9 L, B( `, T
© 2005 Directed Electronics—all rights reserved 9
) K# P, E, R1 ?$ z7 V Z" L2 xThe system can also be programmed to arm the optional Failsafe®
" L' [5 Z! z; x: Q* l* |) k; A; B! ?Starter Kill automatically (called Passive Mode). If the system has* M7 h$ N6 G1 |% H5 T- W
been programmed for Passive Mode, the Failsafe® Starter Kill will2 w( r/ i' m8 W; w I1 T/ d
automatically activate 30 seconds after the ignition has been8 L/ {8 L; C; J/ ~" M
turned off. After the ignition has been turned off, the status LED
" `, W# ]) b$ E0 [$ B, H4 Zwill flash rapidly to indicate that the system is in Passive Mode.
% R# _. u3 b" g1 E: c) }If Passive Mode has been programmed on, then it is also possible
& N' ^! Z1 | y$ y0 G3 h3 zto program the system for Passive Locking. With Passive Locking,
& v1 H6 _6 `* J% ~! v: F! y$ ?8 @the vehicle doors lock automatically at the same time that the Failsafe®
3 k! R- \( d' H* SStarter Kill is activated. If Passive Locking is programmed on, care
6 D* ^& o3 [+ lmust be taken to prevent the keys from being locked in the vehicle.
! C9 z0 N& J% h' ONOTE: For Passive Mode to be effective, the Failsafe® Starter Kill relay! P5 K2 T! J% B {
must be installed.
# x$ E6 Y$ m0 oPressing for one second disarms the system and unlocks the
- R `( |! U+ ?* C4 ?doors (if connected). The horn will honk twice (if connected) and
) H2 L9 W) T6 F6 Nthe parking lights will flash twice to confirm disarming of the system.
1 i* ]" g5 t' s! x- YThe optional Failsafe® Starter Kill will be deactivated. The status" l% L; M0 q/ q& Q6 X
LED will turn off, unless the system is programmed for Passive) {' [" r" d; E
Mode. In Passive Mode, the status LED will flash rapidly when the, z2 G f- {1 G9 a- I: w
system is disarmed. This indicates that the system will re-engage+ L4 z- D! p) b! }7 |
the starter kill and re-lock the doors (if Passive Locking has been8 @; q3 L0 @9 K5 I
programmed) in 30 seconds unless the ignition is turned on.+ \* u8 [0 y% @2 }
Disarming
8 X# W1 u5 J6 G; e. V10 © 2005 Directed Electronics—all rights reserved
" o6 U' j# y* Y. X' ~* OIf your remote transmitter is lost or damaged, you can manually( X2 m. S: e) s& L
override the starter kill. To do this, you must have the vehicle's
2 A# c. Z8 ?( I0 U3 }- o, t3 T/ xignition key and know where the Valet button is located. Be sure9 G( f9 U3 C" w# I2 G/ L$ o* L& r
to check with the installer for the location of the Valet button.
: r! b( d: S* Q' r) BTo override the starter kill, turn
& E j6 T( t- ~9 s$ T% nthe ignition on and press the
% {$ P; @9 w2 zValet button within 10 seconds.
" T& V8 W+ C/ H% m) `' aThe status LED will stop flashing2 b0 u, a$ T; c1 L9 g8 c
and the vehicle should start. If it does not start,
: \/ p( @' ^, |+ C1 [4 a6 Zyou may have waited too long; turn the ignition off and repeat the
Z( }& Y' V$ vprocess.
5 b6 d# d7 W: i' P7 u" QLOCATION OF VALET BUTTON_____________________________
: Z+ ]+ I& h+ J. Y& }You can prevent your system from automatically activating the
/ H5 ~# q5 x- L2 z$ R* xFailsafe® Starter Kill and locking the doors by using Valet Mode.+ ^/ h. r( P+ J* D2 a
This is very useful when washing the vehicle or having it serviced./ C7 \2 o0 A" w: c( |3 ]7 d0 f
In Valet Mode, the starter kill cannot be activated, even with the
; a, D3 P% j% o2 {" Itransmitter, but all convenience functions (door locks, remote" H# V; D/ b% ^+ M2 z) k" F" n2 A2 I
start, etc.) will continue to work normally. |
|